Manage

Security and Compliance

Edited

Everything you need to know for Pleneo network setting.

Everything to provision before a Pleneo room is installed. Give it to whoever approves network changes.

Download

Switch ports

Device

PoE

RoomHub

PoE (802.3af)

RoomVision

PoE (802.3af)

RoomVision XL

PoE+ (802.3at)

RoomDesign Ceiling

PoE 8 W, or PoE+ 22 W for higher output

Sonia Amp

PoE+ (802.3at)

All devices are powered over Ethernet. No mains outlet at the device.

802.1X: supported on the Pleneo device hub, EAP-TLS.

Addressing

The Pleneo device hub has two isolated ports, no bridging. LAN 1 carries control and internet. LAN 2 carries audio and video.

DHCP: enabled by default on all ports.

Link-local fallback: on both ports, 169.254.x.x/16, when no DHCP server answers.

Static: addresses can be set per port on the device, in the web interface.

VLAN: segmentation is supported on both device hub ports. LAN 1 and LAN 2 are intended for separate, segmented networks.

Firewall rules

LAN 1

#

Direction

Source → Destination

Port

1

In

Admin computer → Pleneo device hub

TCP 443

2

In

Pleneo devices → Pleneo device hub

UDP 19153

3

In

PTZ cameras → Pleneo device hub

UDP 45

4

Out

Pleneo device hub → Pleneo Cloud

TCP 443

5

Out

Pleneo device hub → Pleneo devices

TCP 443, TCP 19150–19152

6

Out

Pleneo device hub → third-party devices

TCP 45, TCP 2202

7

Out

Pleneo device hub → PTZ cameras

UDP 52381

Rules 1 and 4 are TLS 1.2+. Rules 2, 3, 5, 6, and 7 are control traffic that never leaves the local network. DHCP (UDP 67 and 68) needs no rule.

LAN 2

Purpose

Multicast group

Port

Clock (PTP)

224.0.1.129–132

UDP 319, 320

Audio flows

239.69.0.0/16, 239.255.0.0/16

UDP 5004, 4321

Discovery

224.0.0.251, 239.255.255.255

UDP 5353, 9875

Permit these groups rather than all multicast.

Media network setup

Real-time audio is multicast, bidirectional UDP on dynamic ports, local only. LAN 2 needs a managed switch.

  • IGMP snooping enabled, with forwarding of unregistered multicast disabled.

  • One IGMP querier on the VLAN, on a switch near the root of the topology. Only one.

  • IGMPv2 or later; IGMPv3 falls back to v2.

  • Gigabit throughout, with non-blocking fabric on busy switches.

  • Energy-efficient Ethernet disabled, as it adds delay variation and disturbs clocking.

Network audio integration

Where the room joins a wider networked audio system, a PTP clock (IEEE 1588-2008) also runs on LAN 2: default profile, domain 0, sensitive to delay variation.

Priority marking: clock 46 (EF) in the highest-priority queue, audio 34 (AF41), all other traffic 0 (BE). Switches must apply layer-3 DiffServ QoS, not layer-2 CoS.

Some audio devices mark clock 56 (CS7) and audio 46 (EF) instead. Confirm the values in use before writing the QoS policy.

Internet

Rule 4 only. Needed for remote management, monitoring, and firmware updates, not for the room to work.

Allow by domain, not by IP. Request the current domain list from Pleneo Support.

The connection must not be filtered or intercepted. Pleneo Cloud uses HTTPS only.

No inbound connection from the internet is required. No public IP on any device.

Security and data

  • All audio, video, and meeting content stays local. AI processing is done on the Pleneo device hub.

  • Pleneo Cloud receives only statistics on device health, status, and usage analytics.

  • Pleneo Cloud is hosted on Microsoft Azure. Pleneo holds and complies with SOC 2 Type 2, ISO/IEC 27001, and ISO/IEC 42001.

  • Access is role-based, and all access is logged.

  • Rooms run fully without internet access, including in air-gapped environments.

On this page

Reference logos reflect clients of the Pleneo Group, including those served by Pleneo, Xilica or other group brands.

© 2026 Pleneo Holdings Pte Ltd